TTi CPX400DP – Dual output 840 watt PowerFlex PSU with USB, RS232, LAN
$1,414.00
Technical Specs
TTi CPX400DP - Dual output 840 watt PowerFlex PSU with USB, RS232, LAN Specs
| Voltage Range | 0V to 60V. |
| Current Range | 0A to 20A. |
| Power Range | Up to 420W subject to power envelope. |
| Voltage Setting | By coarse and fine controls |
| Current Setting | By single logarithmic control |
| Output Mode | Constant voltage or constant current with automatic cross-over. CC indicator lit in constant current mode. |
| Output Switch | Electronic, non isolating. Preset voltage and current limit displayed when Output is off. Output rise time no load <10ms. |
| View Settings | With the output On, the meters show actual voltage and current. The preset levels can be viewed and adjusted at any time by pressing the View Settings button. |
| Status Indication | LED indication of Output On, V/I Limits, CV, CI, Power Limit, Remote, LAN status. Message on meter display for trip condition. |
| Ripple & Noise | Typically <3mV rms, <15mV pk-pk, (5mV rms max.) in CV mode. |
| Load Regulation | Voltage - <0·01% of maximum output for any load change within the PowerFlex envelope (remote sense connected). Current - <0·05% of maximum output for any load change within the PowerFlex envelope. |
| Line Regulation | Voltage - <0·01% of maximum output for a 10% line change. Current - <0·01% of maximum output for a 10% line change. |
| Transient Response | <250µs to within 50mV of setting for a 5% to 95% load change. |
| Temp. Coefficient | Typically <100ppm/°C |
| Output Protection | Forward protection by Over-voltage Protection (OVP) trip. Reverse protection by diode clamp for currents to 3A. |
| OVP Setting/Range | Via screwdriver adjustable preset on front panel. Range 1V to 66V |
| Over-temperature | Output trips off for over-temperature. |
| Safety Interlocks | Operations that could cause an unexpected change in voltage or current settings are interlocked with the output switch. |
| Output Terminals | Universal 4mm safety binding posts on 19mm (0·75”) spacing at front. Screw terminals at rear (CPX400SA, SP & DP only). |
| Sense Selection | Voltage sensing is selected as Local or Remote by front panel switch. |
| Sense Terminals | Sprung loaded screw-less terminals at front. Screw terminals at rear (CPX400SA, SP & DP only). |
| Display Type | Dual 4-digit meters, 10mm (0·39”) LED. |
| Resolution/ Accuracy | 10mV / ± 0·1% of reading ± 2 digits |
| Resolution/ Accuracy | 10mA / ± 0·3% of reading ± 20mA |
| Track Accuracy | Slave voltage = ± (0·1% of Master voltage setting + 10mV) |
| Input Scaling | 0 to 100% control of voltage or current from 0 to 5V or 0 to 10V (selectable) |
| Input Accuracy | Voltage: 0.3% ±20mV. Current: 0.5% ±50mA. Input impedance: 10kW |
| Output Scaling | Set values of 0 to 100% of rated output voltage and current generate 0 to 5V (not isolated) |
| Output Accuracy | Voltage: 0.3% ±20mV. Current: 0.5% ±50mA. Output impedance: 125W |
| Remote On/Off | Output On/Off can be controlled by external switch closure (not isolated) |
| RS-232 | Standard 9-pin D connector. Baud rate 9,600 |
| USB | USB 2.0 connection (backwards compatible with USB 1.x). Operates as a virtual COM port |
| Ethernet (LAN) | Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol for connection to Local Area Network or direct connection to a single PC. |
| LXI Compliance | LAN interface is compliant with LXI class C. (LXI is the abbreviation for Lan extensions for Instrumentation). |
| Resolution/Accuracy | 1mV / ± (0.05% +10mV) |
| Resolution/Accuracy | 1mA / ± (0.3% +5mA) |
| Command Delay | Typically <25ms (this must be added to any of the figures below) |
| Voltage Up Time | <10ms* to 1% |
| Voltage Down Time | <80ms* to 1% (full load); <1.5s* to 1% (no load) |
| AC Input | 110 to 240 volts ±10% 50/60Hz. Installation Category II. |
| Input Power | Single - 625VA, Dual - 1250VA max. |
| Operating Range | +5ºC to +40ºC, 20% to 80% RH |
| Storage Range | -40ºC to + 70ºC |
| Environmental | Indoor use at altitudes up to 2000m, Pollution Degree 2 |
| Cooling | Rear discharge variable speed fan. |
| Safety | Complies with EN61010-1 |
| EMC | Complies with EN61326 |
| Size | Single - 107 x 130 (¼ rack 3U) x 398mm Dual - 210 x 130 mm (½ rack 3U) x 377mm (size excludes feet, knobs and terminals). |
| Weight | Single - 4.25kg (9.35lb), Dual - 6.3kg (13.9lb) |
| IVI Driver | An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows*, HPVEE* etc. |
| USB Driver | An installation file is supplied which calls a standard Windows* USB driver. |
Reviews (0)
You must be logged in to post a review.
Reviews
There are no reviews yet.